Distributors & Wholesalers of Quality Fabrication Equipment

Looking for a specific product?
[et_pb_ecwid admin_label=”Ecwid”]

TMV/ALM 2 Axis CNC Knee Mill With Anilam 3000M CNC Control

SKU TMV/ALM-2
$0.00
In stock
1
Product Details
TMV/ALM 2 Axis CNC Knee Mill With Anilam 3000M CNC Control A PC-based controlled 2 axis (table and saddle ) CNC vertical knee mill. The 3000M System by Anilam offers more programming flexibility with 8 GB hard drives and true conversational programming form. The control can be disconnected to allow the machine to be operated manually with digital readout system.


FEATURES:

Model 3000M-2X 2 axis (table and saddle) CNC system by Anilam.


AC Digital Servo drive systems for X and Y axes travel.


Runs on G-code or conversational programming format.


Precision-ground ballscrews with preloaded ball nut assemblies.


3 axis (table, saddle, quill) digital readout system.


Automatic lubrication system.


Safety hand wheels.


ANILAM 3000M SYSTEM FEATURES
HARDWARE
12.1 TFT Flat screen console


Pentium 266 processor


RS-232 port


3-1/2" floppy disk drive


8 GB hard disc


DSP-2 enhanced motion control system that provides significant increases in productivity by producing high speed machining


SOFTWARE
General operation: automatic/manual/single step mode, feed rate display, tool number/diameter/length offset display, position display, loop counter and dwell time display, various resolutions display, item and parts counter display, automatic and programmable homing, parameter setup, DNC, teach-in mode.


Programming: Input via MDI, RS-232 and floppy disk, networking, inch/metric conversion, absolute/incremental programming, conversational programming, blueprint programming, polar/coordinates programming, help graphics, rotation, mirroring, scaling, triangle calculator, geometry calculator, G-code to conversational converter.


Graphics: automatic fit, window zoom, real time draw graphics, pan zoom, tool display, simulate a section of or the entire program.


Compensations: diameter/radius, length offsets, offset calibration, lead screw compensation, backlash compensation, linear compensation.


Canned cycles: ellipse, frame pocket milling, hole milling, circular pocket, rectangular pocket, full bolt hole pattern, partial bolt hole pattern, basic drilling, irregular pocket with islands, rectangular hole, rectangular profile, face milling circular profile.


For detail information on Anilam 3000M CNC control system, please go to the following web site www.anilam.com


Digital Variable Speed Head (DVS) available:

Why DVS head?
High reliability with fewer moving parts than regular vari speed head

Dynamic brake

Low voltage control

Large Digital rpm display

Fully enclosed display unit

Dependable Inverter Drive System

Machine can run on single phase or 3 phase electricity

Safety device prevents machine from self starting after power failure or after emergency stop being pushed






SPECIFICATIONS:

TMV/ALM-2
Table
Working surface 10x 50
T-slot number, size 3, 5/8
Capacity
Table travel 15.5 x31
Ram travel 18.5
Quill travel; z-axis 5
Knee travel 15.3
Spindle to column 9.8-28.3
Spindle to nose to table 1-1/2-17
Spindle
Motor 3 HP
Wiring voltage 220/440V, 3 phase, 60 H
Taper R-8
Speed (vari speed) 60-4,500 RPM
Quill feed (IPR) 0.0015, 0.003, 0.006
Head swivel 360
Head tilt; left-to-right 45
Head tilt; up-and-down 45
Dimensions and Weight
Floor area 101x74x87
Net weight (lbs) 3650


STANDARD ACCESSORIES:
Hard-chrome ways (LMV, LMV-50)
Hardened and ground box ways (TMV, TMV-1)
Front and rear way covers
Automatic lube system
Tool Kit


OPTIONAL ACCESSORIES:
DVS Head wired 220V
440V Transformer - 3HP
6 Kurt Vise with Swivel Base
R-8 collet set.
Clamping kit.
Right angle milling attachment.
Riser block.
Power drawbar.
Coolant System with Chip Pan At Base
Power Draw Bar
Halogen Work light
Save this product for later
[/et_pb_ecwid]